Thanks for the excellent tutorial. You might want to change the command: "archieve download-sw /force-reload /overwrite t -k9w7-tar.124-21a.JY.tar"and get rid of the first "e" in archive. It had me stumped why I couldn't get it to work. Always pays to read what you copy & paste.
set IP_ADDR 192.168.1.4 [According to my network setup]set NETMASK 255.255.255.0 [According to my network setup]set DEFAULT_ROUTER 192.168.1.7 [According to my network setup]tftp_initether_initflash_inittar -xtract t -k9w7-tar.153-3.JH.tar flash:dir flashset boot flash:/ap3g2-k9w7-mx.153-3.JH/ap3g2-k9w7-mx.153-3.JHsetboot
C1140 K9w7 Tar 12421a Jy Tar
Loading "flash:/c1140-k9w7-tar.124-21a.JY.tar" ...########################################################################### ################################################################################ ################################################################################ ####################
Loading "flash:/c1130-k9w7-mx.124-25d.JA2/c1130-k9w7-mx.124-25d.JA2"...flash:/c1130-k9w7-mx.124-25d.JA2/c1130-k9w7-mx.124-25d.JA2: no such file or directory Error loading "flash:/c1130-k9w7-mx.124-25d.JA2/c1130-k9w7-mx.124-25d.JA2"
I used this method to convert a ciscoap3502 putting a ip on interface g0 . I can ping int intraface for a short time.When I try to run. archive download-sw /force-reload /overwrite t -k9w7-tar.defaultError opening t -k9w7-tar.default no shuch file or directory
Hi. Please I have a challenge. I want to convert a new 2602e with LWAPP to autonomous. I am using PoE. When I set power AP while pressing the mode button, after releasing the button, I get error message on console: %Error opening t -k9w7-tar.default (connection timed out)ap:. have put the two ports on same vlan but cannot ping the AP (10.0.0.1) using my PC (10.0.0.2) that contains the tftp for the image. What more can I do?
this is the output:process_config_recovery: set IP address and config to default 10.0.0.1process_config_recovery: image recoveryimage_recovery: Download default IOS tar image t -k9w7-tar.default
Also, I had to grab another AP and try to associate it with the WLC.While converting a Cisco AP2702i from Autonomous to LWAPP, I tried the following commands several times, but it would still boot with the k9w7 image.
2 -rwx 282 Jan 1 1970 00:10:17 +00:00 info 3 -rwx 6174720 Mar 1 1993 00:21:01 +00:00 ap3g2-rcvk9w8-tar.153-3.JA7.tar 4 -rwx 34650 Mar 1 1993 02:40:31 +00:00 event.log 5 -rwx 1048 Mar 1 1993 02:40:21 +00:00 private-multiple-fs 7 -rwx 13557760 Mar 1 1993 00:24:09 +00:00 ap3g2-k9w8-tar.153-3.JA7.tar 48 drwx 2176 Jan 1 1970 00:16:06 +00:00 ap3g2-k9w7-mx.153-3.JA7 8 -rwx 1765 Mar 1 1993 02:40:21 +00:00 config.txt 9 -rwx 5 Mar 1 1993 02:40:21 +00:00 private-config 10 -rwx 432 Mar 1 1993 02:40:28 +00:00 env_vars
Excellent tutorial. I have one further question. How does one upgrade the boot loader on a Cisco 1142 AP (cisco AIR-AP1142N-N-K9)? The current version on it is (C1140-BOOT-M) Version 12.4(18a)JA and I want to upgrade to 12.4(23c)JA1. The filename is c1140-boot-m.124-23c.JA1.bin, which is the latest. Another site said to use copy t -boot-m.124-23c.JA1.bin bs. I did this and reloaded but nothing has changed. Are you able to show me the process please? There is little info on the interwebs about this. I have upgraded the IOS successfully using your tutorial.
I did mine a little differently. I noticed my ap was only booting up on the ap3g2-rcvk9w8-mx image with is for CAPWAP, but it also had the k9w7 image in the directory as well. I logged in and did my capwap commands to get into cli:debug capwap con clidebug capwap client no-reload 2ff7e9595c
Comments